| Need a 40mm expert | |
|
|
Author | Message |
---|
M14 double-taps Moderator
Posts : 2106 Join date : 2008-07-13 Age : 30 Location : St. Louis, MO
| Subject: Need a 40mm expert Sat Feb 12, 2011 12:08 am | |
| Hey all, recieved my M79 and my Deep Fire 40mm grenade today. M79 launcher is a beaut, but I haven't gotten a chance to fire it due to a problem with the grenade. It wasn't holding gas so I unscrewed it to have a look, and all the parts fell everywhere. After watching youtube vids on similar grenades, I managed to piece this thing back together and figure out the assembly....however it still wouldn't hold gas. So i unscered it again. Now, the tiny tiny ball bearings will not stay in and reassembly is near impossible. Anybody an expert on these? Help? | |
|
| |
Sanguinary Angel Sergeant
Posts : 223 Join date : 2010-05-01 Age : 33
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 12:25 am | |
| ive only used madbull 40mm from asgi. Where did you purchase from? if you can i'd see if you can return it for a new one. i know for my 40mm i have to push in the bottom before i fill it up.
Did you read the directions? lol | |
|
| |
M14 double-taps Moderator
Posts : 2106 Join date : 2008-07-13 Age : 30 Location : St. Louis, MO
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 12:39 am | |
| Push in the bottom? Goddamn I wish I woulda been able to try that.... and no, it didn't come with any. I purchased from ASSmith | |
|
| |
Sanguinary Angel Sergeant
Posts : 223 Join date : 2010-05-01 Age : 33
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 12:51 am | |
| ya you push in the bottom where the pin in your 203 hits it so it resets and air can get let through, but i don\'t know how safe or even if itll work if your ball bearings are loose or missing. | |
|
| |
M14 double-taps Moderator
Posts : 2106 Join date : 2008-07-13 Age : 30 Location : St. Louis, MO
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 12:56 am | |
| I have them all, the buggers just refuse to stay in now! I will probably try again in the morning...I'll post an update. But thanks a BUNCH for the suggestion..I bet it will work. | |
|
| |
DrummerBoyz95 General Grade 2
Posts : 3897 Join date : 2009-05-13 Age : 28 Location : Ventura County, CA
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 3:28 am | |
| Yeah even if it still has gas in it you have to reset it after every shot... I think. I don't really know, I've only messed with them a couple times. | |
|
| |
M14 double-taps Moderator
Posts : 2106 Join date : 2008-07-13 Age : 30 Location : St. Louis, MO
| Subject: Re: Need a 40mm expert Sat Feb 12, 2011 10:42 pm | |
| Yeap, that didn't change a thing | |
|
| |
sticks.13 Moderator
Posts : 1931 Join date : 2008-02-10 Age : 32 Location : C-BUS, Ohio
| Subject: Re: Need a 40mm expert Sun Feb 13, 2011 4:36 pm | |
| cover the bearing holes with white lithium grease, put the bearings back in and recover them in white lithium. This is the easiest was to do it....
sticks | |
|
| |
M14 double-taps Moderator
Posts : 2106 Join date : 2008-07-13 Age : 30 Location : St. Louis, MO
| Subject: Re: Need a 40mm expert Thu Feb 17, 2011 10:47 am | |
| Okay, I got the shell all back together, but i can\'t get ANY gas into the Darn thing! all the gas just sprays everywhere when I try to load it into the valve...I've waisted a whole can of green gas trying to load this thing. | |
|
| |
Sponsored content
| Subject: Re: Need a 40mm expert | |
| |
|
| |
| Need a 40mm expert | |
|