| | JG Bar 10 AirBrake Mod Problem |  |
|
|
| Author | Message |
|---|
Black Out
Private
Posts : 38
Join date : 2009-01-12
Age : 29
|  Subject: JG Bar 10 AirBrake Mod Problem  Fri Apr 24, 2009 8:42 pm | |
| Hey everyone! I was performing the JG Bar 10 airbrake mod and got to the part where you have to take off the cylinder head. It is really, really, REALLY difficult to do! I have seen youtube videos where people just screw it off but i can not. I got my rifle yesterday so any help would be appreciated.
Thanks,
Black Out | |
|
| | |
Russ
Corporal
Posts : 77
Join date : 2008-10-05
Age : 30
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Sat Apr 25, 2009 1:07 am | |
| Thats weird, you usually can just just twist it off. | |
|
| | |
mgunner564
Colonel
Posts : 1303
Join date : 2009-02-03
Age : 113
Location : Maine
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Sat Apr 25, 2009 10:05 am | |
| well get some pliers and grip it tight and TURN!!!! but make sure not to gouge the air brake too much or you might make a hole
the reason other peoples head comes off so easy is because they have taken it off many times | |
|
| | |
Black Out
Private
Posts : 38
Join date : 2009-01-12
Age : 29
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Sun Apr 26, 2009 8:45 pm | |
| Uhg. I used needle-nosed pliers and put paper towel on it and tried to turn but it ripped the paper towel. When I put more layers of paper towel on when i turned it would just turn the paper towel, not letting me to grip the cylinder head. Smae thing for electrical tape. Plaease help me!!! | |
|
| | |
Zane
Major
Posts : 920
Join date : 2008-09-05
Age : 114
Location : In a place
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Sun Apr 26, 2009 9:45 pm | |
| first of don't use needle nose...use a pair of pliers with a grip, wrap a piece of cloth or several layers of paper towel and turn slowly, don't break it by squeezing to hard. and don't turn to hard or you might break it clean of. | |
|
| | |
aveenvp
Major
Posts : 769
Join date : 2009-01-05
Age : 30
Location : Baltimore, MD (USA)
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Wed Apr 29, 2009 10:34 pm | |
| there is a hole on the bottom part of it (not the very top hole!). put an allen wrench into that, use the actual nozzle as a fulcrum, and push to free it. simple physics. | |
|
| | |
Jackofalltrades
Corporal
Posts : 181
Join date : 2009-04-18
Age : 33
Location : Washington
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Mon Jun 08, 2009 5:47 pm | |
| Depending on where you got it, it may have a glue or some other adhesive holding it close so try getting it warm first. | |
|
| | |
TheAirsoftLoki
Private
Posts : 1
Join date : 2009-06-02
| | Subject: Re: JG Bar 10 AirBrake Mod Problem Mon Jun 15, 2009 7:52 pm | |
| It has a pin in the cylinder head. Here is a link on how to get it out Link! | |
|
| | |
Sponsored content
| | Subject: Re: JG Bar 10 AirBrake Mod Problem | |
| |
|
| | |
| | JG Bar 10 AirBrake Mod Problem | |
|
