JG Bar 10 Upgrading

Subject: JG Bar 10 Upgrading Wed Feb 13, 2008 12:27 am

The JG Bar 10. This gun is a great gun to upgrade. First off it is compatible with all TM VSR parts. So if you wanted to totally overhaul it you could do that, but most people that wanted a really reliable and nice sniper probably would have gotten the TM in the first place. So this upgrade guide is aimed at "Noobs" (No Pun Intended) who want to upgrade their rifle without spending any serious dough.

There is 3 easy upgrades:
1.) The Air Brake Mod:
This is a fairly simple procedure that will get the FPS up to around 470-490. First disassemble the cylinder and take out the piston. On the end of the piston is a plastic stick protruding from it. Take a saw and cut to approx. half of its previous length. Just in case you are worried about this affecting some other aspect of your gun it won't do anything negitive performance wise. But it will make your gun louder, but don't worry. No guns even have this silencing feature. The way this works is it creates a seal in the barrel by that little stick going into it. This traps some air inside the cylinder which causes the piston to slow because of the compressed air. So when the piston strikes the piston head it is moving much slower. But then this also reduces the volume of air being exerted through the barrel. Shortening the air brake then allows more air to travel down the barrel more quickly. Thus raising FPS. (Hope I didn't get to nerdy and scientific there.)

2.) The Teflon Tape Mod:
This is another easy mod that will raise FPS. Take Teflon (also known as plumbers tape) tape and wrap it in these area's. Around that outside of the hop-up. On the tip of the cylinder head on the indented part. And finally around the base of the tip of the cylinder head. You can wrap it around the Piston head but I would prefer to go to Home Depot. Buy a case of assorted O-rings and choose the one that would give me the tightest possible seal.

3.) (Note: Don't do this mod if you don't want any thing to break.)
Washer Mod:
OK, I made this one up myself. Take your piston to Home Depot and get some washers that will fit inside of it. Then take some electrical tape and tape them together. Then place them inside the cylinder. What this will do is
A.) Compress the spring more for more FPS.
B.) Give it that recoil effect.
However, the extra weight slamming into the cylinder head will cause fatigue and eventually break something. The raised FPS will cause the sears to wear out quickly. But then you can just but a Zero Trigger system.

Sorry I don't have any pics yet but I'll try to get them soon. If you have questions just PM me.

Happy Hunting

Subject: Re: JG Bar 10 Upgrading Wed Feb 13, 2008 9:19 am

Very interesting... I dont have a bolt action, but if I think about buying one, I will definitely consider the JG just because it looks easy to get high fps with basically free mods. Very Happy

Private Age : 17 Joined : 09 Feb 2008 Posts : 73

Yah the JG is a beast, you can literally get it from 360 fps to 500 in about 5 mins with about $0.99.

I didn't want to get it though, because if i messed it up and it broke, i wouldnt have enough money muh-lah to get a new one.

Subject: Re: JG Bar 10 Upgrading Wed Feb 13, 2008 6:41 pm

Hey if you are worried about messing up, don't be. Its pretty hard to screw up a BAR 10 and like I said you could just PM me. But your choice.

Subject: Re: JG Bar 10 Upgrading Tue Feb 19, 2008 1:12 am

does the teflon tape mod work with the VSR 10????
_________________
ECHO 1 M4 COMMANDO
VSR clone W/ Bushnell 3-9x32E ILL

Private Age : 17 Joined : 09 Feb 2008 Posts : 73

Uh why would you want to do that with such a nice gun? Not sure if it does, i don't know anyone who has tried it...
_________________
"Kill one man, terrorize a thousand."

Subject: Re: JG Bar 10 Upgrading Fri Feb 22, 2008 6:01 pm

yes the Teflon mod should work for you VSR10. the reason i say this is because the Teflon mod is made for the V Hop-Up. the VSR series was the fist style gun to have this V style Hop-Up

sticks

Subject: Re: JG Bar 10 Upgrading Wed Mar 05, 2008 7:49 pm

hey, if teflon tape increases the FPS as drastically as it does... then I would use it, no matter how nice the gun is

Subject: Re: JG Bar 10 Upgrading Fri Mar 28, 2008 6:11 pm

Funny now that, a month and a half later, Seabass now has the Bar 10.
_________________
The (not so) Lone Fox is Out

Hey got a question just throw me a PM (unless it is about the Bar 10 ...that word makes me shiver)

Subject: Re: JG Bar 10 Upgrading Sat Mar 29, 2008 11:29 am

I have had it a while... I need to post the results from the mods. I am waiting on a nice day with low wind.
_________________
Classic Army MG36 - 2500 rounds of pure fury.
Echo 1 Vector Arms AK - 400 FPS
JG Bar 10 G-Spec - 520 FPS
ICS M4 CQB - 325 FPS (Perfect for close encounters)